Wishing our customers all the best of health in the current climate!

Vent Axia 443028 Sentinel Kinetic Plus B Heat Recovery Unit, Summer Bypass & Integral Humidistat

£1,100.00
£1,320.00 (inc. VAT)
£1,683.17
Information
Vent Axia 443028 Sentinel Kinetic Plus B Mechanical Ventilation with In Built Heat Recovery Unit, Summer Bypass & Integral Humidistat
 

Increased Performance

The Sentinel Kinetic Plus benefits from the latest high efficiency, backward curved impeller design, ensuring the lowest possible energy consumption, ultra quiet operation and an exceptional performance range covering small one bed apartments to the largest of houses.

Care Homes & Student Accommodation

The Sentinel Kinetic Plus is ideal for larger homes and multiple occupancy units such as care homes and student accommodation. Capable of 400m3/hr at 150Pa, the unit can extract from up to ten bathrooms and a communal kitchen while still achieving almost 90% heat recovery. The fully automatic capability of the Kinetic range means that adequate ventilation is always achieved.

The Kinetics BMS capability is also ideal for those commercial applications where landlords or property managers want to monitor and optimize building performance and maintenance. The Kinetic BMS can provide status information and its self diagnostics can report if any fault is found.

Spigot Options

Spigots may be re-positioned to give horizontal connection or a combination of vertical and horizontal connection. Optional 180mm/200mm spigots can simplify connection in commercial installations where larger diameter duct work has been used.

Quick Change Filter

As many systems are placed within cupboards the unique filter design folds as you remove it to ensure easy access in restricted spaces.

Integral Humidity Sensor

The integral humidity sensor increases speed in proportion to relative humidity levels, saving energy and reducing noise. The sensor also reacts to small but rapid increases in humidity, even if the normal trigger threshold is not reached. This unique feature ensures adequate ventilation, even for the smallest wet room. The night time relative humidity setback feature suppresses nuisance tripping as humidity gradually increases with falling temperature.

Click for more information about the range

Range Product Specification

The Lo-Carbon Sentinel Kinetic Plus has 2 fully adjustable speeds and a purge setting - maximum. On the front of the unit is a digital controller that can be used to pre-set the speeds to any required air-flow within the performance range.

The Sentinel Kinetic Plus models can be mounted vertically in a roof space or on a suitable wall. When mounted in an unheated area ducting should be insulated. Ducting can be attached to the unit horizonally, vertically or both.
Left or right hand installation. The unit is supplied with duct spigots to outside on the right hand side. These can be reversed onsite by simply removing the control panel, rotating the unit 180 degrees and re-attaching the control panel.
Horizontal and vertical spigots: The combination of spigot options allows installation in confined locations. If vertical and horizontal connection is required on the same outlet/inlet, additional spigots can be supplied.
Condensate drain can be taken out through the back, bottom or front of the unit. Using the fittings supplied, the final condensate connection is made outside the unit and can be completed after installation.

Typical Range Specifications

Supply and install a Sentinel Kinetic Plus system Wholehouse heat recovery unit as manufactured by:

Vent-Axia Clean Air Systems
Fleming Way
Crawley
West Sussex
RH10 9YX

Performance: m Degree/h l/s
Max ventilation rate 400 at 150Pa 111
N Degree speed settings 3 (variable between 10% and 100%)

Efficiency: The unit should retain up to 92% of the temperature differential of out going air.

Heat exchanger: should be of a multi plate counter-flow type constructed out of PETG with ultra sonic welded joints.

Motor: should be a Lowatt Energy Saving DC with ball bearings, greased for life. It shall operate up to an ambient temperature of 40 DegreeC and be fitted with an electronic thermal overload protective device.

Fan: The fan impeller should be of a backward curved centrifugal type, dynamically balanced.

Controls: The unit should contain an integral driver circuit permits connection to Switched Live, No-volt and 0v to 10v Proportional Input.

Ducting spigots: The unit should provide 150mm Degree x 50mm long spigots for all duct connections with vertical and horizontal locations. (Can be converted to flat ducting).

Filter: should be synthetic material tested to minimum of EU3.

Condensation: The outlet provided should offer front, rear and bottom connections external to the unit.

Construction: The unit outer case should be constructed of white ABS. The heat exchanger access doors should give tool-free access to the filters.

Mounting: Vertical, floor or wall mounted, or within a cupboard.

Mains electrical supply: 230VAC 50Hz.

Complies to the following approvals/directives: CE, LVD, EMC. SAP Appendix Q eligible.

Specifications
  • MPN:
    443028
  • EAN:
    Does not apply
  • EAN:
    Does not apply
  • Brand:
    Vent Axia
  • Condition:
    New
  • Product Code:
    443028
  • Weight:
    24kg